Biology subjects

Petrone, N.

Publications and source records attributed to Petrone, N..

3 recordsLinked to original sources

bioRxiv2026

Mechanical fidelity of brain tissue phantoms: A comparative experimental characterization of equilibrium and dissipative behavior

Despite lacking a dedicated structural function, brain tissue is exposed to severe mechanical loading during accidents and trauma, with potentially permanent or lethal consequences. Therefore, characterizing its mechanical behavior assumes particular importance for designing protective equipment, planning surgeries, and training neurosurgeons, tasks that often rely on physical brain replicas made from phantom materials. Although the mechanics of brain tissue has been extensively studied, the selection of suitable phantom materials still relies on simplified metrics that fail to capture the highly nonlinear and rate-dependent behavior of the brain. In this work, we characterize the mechanical response at low-to-medium strain rates of common synthetic brain phantom materials, including Sylgard 527, Ecoflex Gel, and a composite hydrogel, and establish rigorous comparisons with porcine brain tissue as a benchmark. To this end, we employ a multi-step stress relaxation protocol under both uniaxial extension and compression across two different strain rates, introduce thermodynamic metrics, and perform comparisons based on rigorous statistical analysis. In particular, we isolate the thermodynamic equilibrium stress-strain curves, representing the baseline material's response, from rate-dependent dissipative inelastic effects, relatable to viscoelastic and poroelastic mechanisms. Our results provide a thorough comparison, revealing critical limitations in existing simulant materials and highlighting significant space for developing improved brain surrogates. The comprehensive dataset collected can also support the calibration of constitutive models, enhancing the predictive accuracy of numerical simulations involving brain tissue and its surrogates. More broadly, this study highlights the need to move beyond simplistic, scalar-metric-based comparisons of mechanical responses across materials.

biophysics↗

bioRxiv2021

Interpersonal synchronization of movement intermittency

Most animal species group together and coordinate their behavior in quite sophisticated manners for mating, hunting or defense purposes. In humans, coordination at a macroscopic level (the pacing of movements) is evident both in daily life (e.g., walking) and skilled (e.g., music and dance) behaviors. By examining the fine structure of movement, we here show that interpersonal coordination is established also at a microscopic - sub-movement - level. Natural movements appear as marked by recurrent (2-3 Hz) speed breaks, i.e., submovements, that are traditionally considered the result of intermittency in (visuo)motor control. In a series of interpersonal motor coordination tasks, we demonstrate that submovements are not independent between interacting partners but produced in a tight temporal relation that reflects the directionality in the partners informational coupling. These findings unveil a potential core mechanism for behavioral coordination that is based on between-persons synchronization of the intrinsic dynamics of action-perception cycles.

neuroscience↗

bioRxiv2018

Multifunction control and evaluation of a 3D printed hand prosthesis with the Myo armband by hand amputees

Upper limb amputations are highly impairing injuries that can substantially limit the quality of life of a person. The most advanced dexterous prosthetic hands have remarkable mechanical features. However, in most cases, the control systems are a simple extension of basic control protocols, making the use of the prosthesis not intuitive and sometimes complex. Furthermore, the cost of dexterous prosthetic hands is often prohibitive, especially for the pediatric population and developing countries. 3D printed hand prostheses can represent an opportunity for the future. Open 3D models are increasingly being released, even for dexterous prostheses that are capable of moving each finger individually and actively rotating the thumb. However, the usage and test of such devices by hand amputees (using electromyography and classification methods) is not well explored. The aim of this article is to investigate the usage of a cost-effective system composed of a 3D printed hand prosthesis and a low-cost myoelectric armband. Two subjects with transradial amputation were asked to wear a custom-made socket supporting the HANDi Hand and the Thalmic Labs Myo armband. Afterwards, the subjects were asked to control and use the prosthetic hand to grasp several objects by attempting to perform a set of different hand gestures. Both the HANDi Hand and the Myo armband performed well during the test, which is encouraging considering that the HANDi Hand was developed as a research platform. The results are promising and show the feasibility of the multifunction control of dexterous 3D printed hand prostheses based on low-cost setups. Factors as the level of the amputation, neuromuscular fatigue and mechanical limitations of the 3D printed hand prosthesis can influence the performance of the setup. Practical aspects such as usability and robustness will need to be addressed for successful application in daily life. A video of the tests can be found at the following link: https://youtu.be/iPSCAbd17Qw

bioengineering↗